Quality Finishes That Last a Lifetime

TWO PACK WATER BASED POLYURETHANE CLEAR WOOD FINISH FOR EXTERIORS

Pack Sizes

  • 1 Ltr

Features

  • 5 - Best in Class

  • 4 - Very Good

  • 3 - Good

  • 2 - Average

  • 1 - Poor

- Available in both Glossy and Matt Finishes

- Lead Content - Less than 90 PPM

Surface Preparation

The raw wooden surface to be coated should be clean, dry, free from moisture ,dampness and other contamination

For hard wood, sand the surface using Sandpaper #80, followed by Sandpapers #120, #150, #180 and #220

For Veneer ply surfaces,start with Sandpaper #220

This step wise approach makes the surface smooth

Always sand in the direction of the wood grain

Apply Using

  • 1 Ltr

    Manual Brush Application

  • 1 Ltr

    Conventional Spray, Nozzle orifice: 0.059 inches, Pressure: 35 - 45 psi

Thinning Details

  • Thinner Recommended - Demineralised Water

AquaCoat 2K PU Sealer/ Glossy/ Matt 25 - 30%

Application Procedure

Mix the base prior to mixing with the hardener. DO NOT SHAKE THE CONTAINER.

Mix the base and hardener thoroughly before addition of de – mineralised water.

Avoid applying in direct sunlight or when the humidity is very high.

CLOSED PORE FINISHES

Apply 2 to 3 coats of Aquacoat 2K PU Sealer clear with an interval of 8 hrs between the subsequent coats

Sandpaper #220 can be used for the first coat and Sandpaper # 400 can be used for the second and third coats

The number of coats of sealer required varies from 2 to 3 depending on the absorption of wood

Apply 2 coats of Aquacoat 2K PU Glossy / Matt clear, depending on the requirement, with an Interval of 8hours between subsequent coats. Sanding of the first coat shall be done using Sandpaper # 600

MRF Aquacoat Woodstains Interior shades can be used to enhance the colour of the wood grain. The available shades can be used over either the first coat or the second coat of sealer clear sanding of the applied shade is not permitted

OPEN PORE FINISHES

Apply 3 to 4 coats of Aquacoat 2K PU Glossy / Matt clear directly on raw wood with an interval of 8 hrs between each coat

Sanding should be done prior to the application of each coat with Sandpaper # 400 for the first coat and Sandpaper # 600 for the subsequent coats

SINGLE PACK WATER BASED POLYURETHANE CLEAR WOOD FINISH FOR INTERIORS

Pack Sizes

  • 1 Ltr

Features

  • 5 - Best in Class

  • 4 - Very Good

  • 3 - Good

  • 2 - Average

  • 1 - Poor

- Available in both Glossy and Matt Finishes

- Lead Content - Less than 90 PPM

Surface Preparation

The raw wooden surface to be coated should be clean, dry, free from moisture ,dampness and other contamination

For hard wood, sand the surface using Sandpaper #80, followed by Sandpapers #120, #150, #180 and #220

For Veneer ply surfaces,start with Sandpaper #220

This step wise approach makes the surface smooth

Always sand in the direction of the wood grain

Apply Using

  • 1 Ltr

    Manual Brush Application

Thinning Details

  • Thinner Recommended - Demineralised Water

AquaCoat 1K PU Sealer/ Glossy/ Matt 5 - 8%

Application Procedure

Mix the base thoroughly prior to application. DO NOT SHAKE THE CONTAINER.

Avoid applying in direct sunlight or when the humidity is very high.

CLOSED PORE FINISHES

Apply 2 to 3 coats of Aquacoat 1K PU Sealer clear with an interval of 8 hrs between the subsequent coats

Sandpaper #220 can be used for the first coat and Sandpaper # 400 can be used for the second and third coats

The number of coats of sealer required varies from 2 to 3 depending on the absorption of wood

Apply 2 coats of Aquacoat 1K PU Glossy / Matt clear, depending on the requirement, with an Interval of 8 hours between subsequent coats. Sanding of the first coat shall be done using Sandpaper # 600

MRF Aquacoat Woodstains Interior shades can be used to enhance the colour of the wood grain. The available shades can be used over either the first coat or the second coat of sealer clear. Sanding of the applied shade is not permitted

OPEN PORE FINISHES

Apply 3 to 4 coats of Aquacoat 1K PU Glossy / Matt clear directly on raw wood with an interval of 8 hrs between each coat

Sanding should be done prior to the application of each coat with Sandpaper # 400 for the first coat and Sandpaper # 600 for the subsequent coats

Aquacoat 2K PU is a two pack water based polyurethane clear for wooden floors

Pack Sizes

  • 1 Ltr

Features

  • 5 - Best in Class

  • 4 - Very Good

  • 3 - Good

  • 2 - Average

  • 1 - Poor

- Available in both Regular and Anti-Skid Finishes

- Lead Content - Less than 90 PPM

Surface Preparation

The raw wooden surface to be coated should be clean, dry, free from moisture ,dampness and other contamination

For hard wood, sand the surface using Sandpaper #80, followed by Sandpapers #120, #150, #180 and #220

For Veneer ply surfaces,start with Sandpaper #220

This step wise approach makes the surface smooth

Always sand in the direction of the wood grain

Apply Using

  • 1 Ltr

    Manual Brush Application

  • 1 Ltr

    Conventional Spray, Nozzle orifice: 0.059 inches, Pressure: 35 - 45 psi

Thinning Details

  • Thinner Recommended - Demineralised Water

AquaCoat 2K PU Floor coat / Anti-Skid Floor coat 25 - 30%

Application Procedure

Mix the base prior to mixing with the hardener. DO NOT SHAKE THE CONTAINER.

Mix the base and hardener thoroughly before addition of de – mineralised water.

Avoid applying in direct sunlight or when the humidity is very high.

CLOSED PORE FINISHES

Apply 2 to 3 coats of Aquacoat 2K PU Sealer clear with an interval of 8 hrs between the subsequent coats

Sandpaper #220 can be used for the first coat and Sandpaper # 400 can be used for the second and third coats

The number of coats of sealer required varies from 2 to 3 depending on the absorption of wood

Apply 2 coats of Aquacoat 2K PU Floorcoat / Anti skid Floorcoat clear, depending on the requirement, with an Interval of 8hours between subsequent coats. Sanding of the first coat shall be done using Sandpaper # 600

MRF Aquacoat Woodstains shades can be used to enhance the colour of the wood grain. The available shades can be used over either the first coat or the second coat of sealer clear sanding of the applied shade is not permitted

OPEN PORE FINISHES

Apply 3 to 4 coats of Aquacoat 2K PU Floorcoat clear directly on raw wood with an interval of 8 hrs between each coat

Sanding should be done prior to the application of each coat with Sandpaper # 400 for the first coat and Sandpaper # 600 for the subsequent coats

Register your purchase details

  • Upload Invoice Copy