Quality Finishes That Last a Lifetime

MULTI-PURPOSE PREMIUM TWO PACK POLYURETHANE CLEAR AND PIGMENTED TOPCOATS

Pack Sizes

  • 500 ml,1 Ltr,4 Ltrs and 20 Ltrs

69 Shades

Features

  • 5 - Best in Class

  • 4 - Very Good

  • 3 - Good

  • 2 - Average

  • 1 - Poor

- Available in Clear, Glossy, Metallic and Matt Finishes

- Lead Content - Less than 90 PPM

Surface Preparation

The surface to be coated should be clean and free from contamination

Mill scale and rust should be completely removed either by mechanically abrading the surface or through abrasive blast clean technique

The substrate should be free from dew as it directly relates to premature product failure

Apply Using

  • 1 Ltr

    Conventional Spray, Nozzle orifice: 0.059 inches, Pressure: 35 - 45 psi

Application Procedure

Mix the base thoroughly prior to mixing with the hardener

Avoid applying in direct sunlight or when the humidity is very high

For application details, please refer product data sheet in downloads menu

MULTI-PURPOSE PREMIUM TWO PACK POLYURETHANE CLEAR AND PIGMENTED TOPCOATS

Pack Sizes

  • 1 Ltr, 4 Ltrs and 20 Ltrs

2000 Shades

Features

  • 5 - Best in Class

  • 4 - Very Good

  • 3 - Good

  • 2 - Average

  • 1 - Poor

- Available in Clear, Glossy, Metallic and Matt Finishes

- Eco-friendly Lead Content - Less than 90 PPM

Surface Preparation

The surface to be coated should be clean and free from contamination

Mill scale and rust should be completely removed either by mechanically abrading the surface or through abrasive blast clean technique

The substrate should be free from dew as it directly relates to premature product failure

Apply Using

  • 1 Ltr

    Conventional Spray, Nozzle orifice: 0.059 inches, Pressure: 35 - 45 psi

Application Procedure

Mix the base thoroughly prior to mixing with the hardener

Avoid applying in direct sunlight or when the humidity is very high

For application details, please refer product data sheet in downloads menu

MULTI-PURPOSE PREMIUM SINGLE PACK ACRYLIC PIGMENTED FINISH

Pack Sizes

  • 100 ml,200 ml,500 ml,1 Ltrs and 4 Ltrs

5 Shades

Features

  • 5 - Best in Class

  • 4 - Very Good

  • 3 - Good

  • 2 - Average

  • 1 - Poor

- Lead Content - Less than 90 PPM

Surface Preparation

The surface to be coated should be clean and free from contamination

Mill scale and rust should be completely removed either by mechanically abrading the surface or through abrasive blast clean technique

The substrate should be free from dew as it directly relates to premature product failure

Apply Using

  • 1 Ltr

    Conventional Spray, Nozzle orifice: 0.059 inches, Pressure: 35 - 45 psi

Thinning Details

Thinner Recommended

Acrylic Super Fine Finishes Thinner for Finish / Thinner 3002

Thinner Intake

Acrylic Super Fine Finishes 60-80% (Thinner for finish)100-120% (Thinner 3002)

Application Procedure

Mix the base thoroughly prior to application.

Avoid applying in direct sunlight or when the humidity is very high

For application details, please refer product data sheet in downloads menu

MULTI-PURPOSE ECONOMICAL TWO PACK POLYURETHANE PIGMENTED TOPCOATS

Pack Sizes

  • 1 Ltr, 4 Ltrs and 20 Ltrs

28 Shades

Features

  • 5 - Best in Class

  • 4 - Very Good

  • 3 - Good

  • 2 - Average

  • 1 - Poor

- Lead Content - Less than 90 PPM

Surface Preparation

The surface to be coated should be clean and free from contamination

Mill scale and rust should be completely removed either by mechanically abrading the surface or through abrasive blast clean technique

The substrate should be free from dew as it directly relates to premature product failure

Apply Using

  • 1 Ltr

    Conventional Spray, Nozzle orifice: 0.059 inches, Pressure: 35 - 45 psi

Application Procedure

Mix the base thoroughly prior to mixing with the hardener

Avoid applying in direct sunlight or when the humidity is very high

For application details, please refer product data sheet in downloads menu

MULTI-PURPOSE SINGLE PACK SOLVENT BASED PU ENAMEL

Pack Sizes

  • 200 ml,500 ml,1 Ltr,4 Ltrs and 20 Ltrs

24 Shades

Features

  • 5 - Best in Class

  • 4 - Very Good

  • 3 - Good

  • 2 - Average

  • 1 - Poor

-

Surface Preparation

Metal

Ensure that the surface is dry, clean and free from impurities like oil, grease, loose rust and cracked or flaked paint

Sand the surface with #180 Sandpaper and ensure that no loose particles are present before priming. Wipe the surface clean

Wood

The raw wooden surface to be coated should be clean, dry, free from moisture, dampness and other contamination

Sand the surface using #80 Sandpaper, followed by grit sizes #120, #150, #180 and #220 Sandpaper

This step wise approach leads to a very smooth surface

Always sand in the direction of the wood grain. This step wise process is applicable only for hard wood. Start with #220 Sandpaper for Veneer/ Plywood

Thinning Details

  • 1 Ltr

    Mix the paint thoroughly prior to thinning

  • 1 Ltr

    Thinner Recommended - Thinner 555

Thinner Intake for spray 30 - 35%
Thinner Intake for brush 15 - 20%

Application Procedure

Metal

Apply 2 coats SPEP Primer Grey with an interval of 4-6 hours between subsequent coats either by spray or brush

The primed surface can be sanded using #220 Sandpaper after 10-12 hours of drying.

Appropriate filler to be used for filling dents and imperfections which should then be sanded and primed again.

Apply 2 coats of Specta Glossy/Stain shede with an interval of 6-7 hours by brush or spray.

Wood

Apply 2 to 3 coats of MRF Vapocure paints Wood Primer with an interval of 5-6 hours between subsequent coats.

Sanding should be done prior to application of Topcoat.

#400 Sandpaper can be used for sanding after 10-12 hours of drying.

Apply 2 coats of Specta Glossy/Stain shede with an interval of 6-7 hours by brush or spray.

PREMIUM TWO PACK POLYURETHANE PIGMENTED WOOD FINISH FOR INTERIORS

Pack Sizes

  • 1 Ltr, 4 Ltrs and 20 Ltrs

1110 Shades

Features

  • 5 - Best in Class

  • 4 - Very Good

  • 3 - Good

  • 2 - Average

  • 1 - Poor

- Lead Content - Less than 90 PPM

Surface Preparation

The raw wooden surface to be coated should be clean, dry, free from moisture ,dampness and other contamination

For hard wood, sand the surface using Sandpaper #80, followed by Sandpapers #120, #150, #180 and #220

For Veneer ply surfaces,start with Sandpaper #220

Always sand in the direction of the wood grain

Apply Using

  • 1 Ltr

    Conventional Spray, Nozzle orifice: 0.059 inches, Pressure: 35 - 45 psi

Thinning Details

  • Thinner Recommended - Thinner for finish

WoodCoat Ultra Int.Sealer White 20 - 25%
WoodCoat Ultra Int.High Gloss White 30 - 35%
WoodCoat Ultra Int. Matt White 15 - 20%
WoodCoat Ultra Int.High Gloss Clear 25 - 30%
WoodCoat Ultra Int. Matt Clear 20 - 25%

Application Procedure

Mix the base thoroughly prior to mixing with the hardener

Avoid applying in direct sunlight or when the humidity is very high

WoodCoat Ultra White

Apply 2 to 3 coats of WoodCoat Ultra Interior Sealer white with an interval of 2 hrs between the subsequent coats. Sanding should be done prior to the application of each coat

Sandpaper #220 can be used for the first coat and Sandpaper #400 can be used for the second and third coats, number of coats of sealer required varies from 2 to 3 depending on the absorption of wood

Apply 2 coats of either WoodCoat Ultra Interior High Gloss White / Matt White depending on the requirement, with an interval of 5 hrs between subsequent coats. Sanding of the first coat shall be done using Sandpaper #600 or #1000

WoodCoat Ultra Other Shades

Apply one coats of WoodCoat Ultra Interior Sealer white followed be 2 to 3 coats of WoodCoat Ultra Interior coloured sealer (tinted) with an interval of 2 hrs between the subsequent coats

Sandpaper #220 shall be used for the first coat and Sandpaper #400 shall be used for subsequent coats

Apply 2 coats of either WoodCoat Ultra Interior High Gloss Clear / Matt Clear depending on the requirement, with an interval of 5 hrs between subsequent coats. Sanding of the first coat shall be done using Sandpaper #600 or #1000

Register your purchase details

  • Upload Invoice Copy